	C-SDOOR Translate

Keyboard shortcut: CD, DRC
Toolbar button:
Compatible with AutoCAD Versions: 13, 14, 2000, 2000i, 2002, 2004, 2005, 2006, 2007, 2008

CENTERED SINGLE DOOR

Command to center a single door in a wall. You will be prompted for the point to center the door on then asked to select the lines/plines/mlines that make up the wall. Once this is done you are asked to select the door size you want. Finally the command will break the walls and allow you to select to which side the door should swing.

User configurable options:

Door appearance - See Customizing door blocks
Thickness for jambs
Max width for jambs
Draw door stops on jambs?
Minimum framing distance on each side of door
Draw door headers?
Draw door sills/thresholds?
Draw demolition Lines? Select layers that are treated as "existing walls"

See Door Commands in the Floor Plan Cmds section of the APS Configuration Utility.

Layers:

If you are using "No Layer Control" the door, jamb, sill, demo lines, and/or header lines (if any) will be inserted/drawn on whatever layer is current. See the Layer Control section of the APS Configuration Utility.

The default layer type for doors and jambs (if any) is "Doors", the default layer type for sill lines is "Finishes", the default layer type for demolition lines (if any) is "Demolition", and the default layer type for header lines (if any) is "Headers".
- If you are using "Direct Layer Assignment" the layer names are assigned to these layer types in the Layer assignments portion of the Layer Control section of the APS-CONFIG command.
- If you are using "Layer Schemes" the layer names are assigned to these layer types in the Assigning Layer Names to Layer Types portion of the SCHEMEDIT command.
The layer types for this command can be changed in the Assigning Layer Types to Commands portion of the Layer Control section of the APS-CONFIG command.

Known limitations:

This command will only insert a door in walls constructed of lines, polylines, and/or mlines.
Submit a limitation not listed.

Alternate uses:

None reported. If you have an alternate use for this command submit it here.

SAMPLE C-SDOOR COMMAND SYNTAX:

Command:
Command: CD
Command: DRC
Command: C-SDOOR

Select base point on which to center single door or <Enter>/<Space> for MID2PT:

If the center of the wall can be found by using the midpoint of one of the wall lines, select the midpoint of that wall line now. The midpoint snap is added to your running object snaps if it is not already being used. If the base point location cannot be found using one of the standard object snaps press <Enter> or <Space> and use the MID2PT option which can locate the base point midway between any two points selected.

Select a point outside the wall lines to place the single door in:

Select the point.

Select a second point crossing all of the lines that make up the wall:

Select the second point of the crossing line that crosses the lines/plines/mlines that make up the wall. The following dialog will appear:

The maximum door size is displayed at the top of the dialog ( the max width shown above is 6'-5"). This distance reflects any minimum framing widths that have been set up. (See Door Commands in the Floor Plan Cmds section of the APS Configuration Utility) If the door size that you need to enter is larger than the "Maximum door size" shown at the top it is possible to override the minimum framing requirements and insert a door size that is equal to the full length of the wall.

Enter the size for the door. Note, this is just the size for the door and is not a rough opening size, the jamb thickness (if any) will be added to this value.

-- The walls will be broken now and any jambs, sill lines, header lines, and/or demo lines will be drawn -- Several door swing options will be drawn --

Select door handing/type desired:

The door type and swing options are shown dashed. Select the one that you would like. If you don’t want any of them just press <Enter> or <Space> and all the door choices will be removed leaving just an opening. Should you miss one of the choices and erase all of them by mistake you may "OOPS" them all back and erase the ones you don’t want manually. You have your choice of: 45, 90, and 180 degree swings and pocket doors. Selecting the door as shown above leaves: